Difference between revisions of "Schematics"
(→Programming connector) |
|||
| (One intermediate revision by the same user not shown) | |||
| Line 13: | Line 13: | ||
[[File:DS1052E HW58 PCB Schematics - Keypad PCB.jpg|700px]] | [[File:DS1052E HW58 PCB Schematics - Keypad PCB.jpg|700px]] | ||
| + | |||
| + | LED Shift Register connected to SPORT0 from Blackfin | ||
== Trigger input front-end == | == Trigger input front-end == | ||
| Line 67: | Line 69: | ||
== Programming connector == | == Programming connector == | ||
| − | + | Looks like the default Blackfin Connector. Tests are outstanding. | |
| − | |||
| − | |||
Latest revision as of 18:50, 11 June 2020
Here you will find some schematics from the Rigol DS1052/DS1102 Hardware Revision 58. The drawings comes from the user A Helene.
Contents
CH1 Analog Frontend
DAC, Demux, Sample & Hold, Buffers
Keypad PCB
LED Shift Register connected to SPORT0 from Blackfin
Trigger input front-end
Trigger, Comparator
Power Supply Unit
Asynchronous Memory Bus
-------------------------------------------------------------------------------------- | - Asynchronous Memory bus: | |------------------------------------------------------------------------------------| | Blackfin | CPLD | FPGA | LA | FLASH |ISP1362 | |-----------------------------------------+-------+-------+--------+--------+--------| |BF.162: ARDY [I] Ready control (N/C) | | | | | | |BF.154: /AOE [O] Output Enable | | | LH1.07 | FLR.28 | | |BF.153: /ARE [O] Read Enable | LT.85 | FP.E1 | LH1.10 | | | |BF.152: /AWE [O] Write Enable | LT.86 | FP.E2 | LH1.09 | | | |BF.161: /AMS0 [O] Bank Select 0 | LT.82 | | | | | |BF.160: /AMS1 [O] Bank Select 1 | LT.81 | | | | | |BF.159: /AMS2 [O] Bank Select 2 | LT.80 | FP.L8 | | | | |BF.158: /AMS3 [O] Bank Select 3 | LT.79 | | | | | |BF.051: PF0/SS0 [?] ? (Pulled high) | | | | | | |BF.050: PF1/SS1 [I] LA Ready (?) | | | LH1.06 | | | |BF.049: PF2/SS2 [I] USB INT1 output | | | | | USB.30 | |BF.034: PF10 [I] USB INT2 output | | | | | USB.31 | |BF.149: AADDR0 [O] USB A0: Command/Data | | | | | USB.61 | |BF.148: AADDR1 [O] USB A1: Device/Host | | | | | USB.62 | | N/C [-] USB /RD input | LT.99 | | | | USB.20 | | N/C [-] USB /CS input | LT.100| | | | USB.21 | | N/C [-] USB /WR input | LT.01 | | | | USB.22 | | N/C [-] LA ? | LT.83 | | LH1.08 | | | | N/C [-] LA ? | | FP.F6 | LH1.24 | | | | N/C [-] FLASH /WP | LT.91 | | | FLR.14 | | | N/C [-] FLASH /CE | LT.98 | | | FLR.26 | | | N/C [-] FLASH /WE | LT.97 | | | FLR.11 | | | N/C [-] FLASH ADDR19 | LT.96 | | | FLR.09 | | | N/C [-] FLASH ADDR20 | LT.95 | | | FLR.10 | | | N/C [-] FLASH ADDR21 | LT.94 | | | FLR.13 | | --------------------------------------------------------------------------------------
BF.x are the pins of BlackFin, [x] is the BlackFin pins direction, LT.x are the pins of the LaTtice CPLD, FP.x the pins of the Altera FPga, LH1.x those of the Logic Analyser Header 1 (the 40 pins one), FLR.x those of the Spansion FLash Ram and USB.x the pins of the Philips ISP1362 USB On-The-Go controller. All the components above share the same 16-bits data bus and the 21-bit Address bus; the BlackFin address bus is 19-bits wide, the address bus width of the CPLD, the FPGA and the Logic Analyser is 8-bits and the USB chip is controlled by the two lower address bus lines.
Programming connector
Looks like the default Blackfin Connector. Tests are outstanding.
